Kitchen Sink Faucet Aerator Cleaning and Replacement Guide for Florida Homes
By James Evans
## Kitchen Sink Faucet Aerator Cleaning and Replacement Guide for Florida Homes
The aerator screwed onto the tip of a kitchen faucet spout is a small, inexpensive device that dramatically affects the faucet's performance. It introduces air into the water stream, reducing flow volume while maintaining useful water pressure, and it filters out particles that enter the water supply line. When Tampa Bay's hard water from the Floridan Aquifer deposits calcium and magnesium scale inside the aerator mesh screens, the result is reduced flow, an uneven spray pattern, or complete blockage of one or more of the aerator's mesh screens. Because hard water mineral deposits are relentless in Hillsborough County's water supply, aerator maintenance is a task that Tampa Bay homeowners face more often than homeowners in areas with softer water.
Best Bay Services handles plumbing fixture maintenance throughout Tampa Bay. Call (813) 416-8676 to schedule.
### How a Faucet Aerator Works
The aerator at the end of the faucet spout contains a housing with one or more screens and a flow restrictor. As water passes through, the screens break the stream into fine channels that mix with air, producing a smooth, aerated flow that reduces splashing and uses less water than an open unrestricted stream. Most residential kitchen faucet aerators are rated at 2.2 gallons per minute (GPM) under standard pressure. Water-efficient aerators are rated at 1.5 GPM or lower.
The aerator housing can be one of two configurations:
**External thread aerators** screw onto threads on the outside of the faucet spout tip. These are the most common configuration for older faucets and many standard kitchen faucets. The aerator can be unscrewed by hand or with slip-joint pliers with a cloth to protect the finish.
**Internal (cache) thread aerators** sit recessed inside the spout tip, hidden from view. These require a special key tool (usually supplied with the faucet) to remove. If you cannot see any visible aerator threads at the spout tip, look inside the spout opening -- a recessed aerator is typically visible as a mesh screen set a quarter to half inch inside the spout.
### Signs the Aerator Needs Cleaning or Replacement
**Reduced flow rate.** Water flows more slowly than it did when the faucet was new, even though water pressure elsewhere in the home is normal. The aerator screens are partially clogged.
**Uneven or spray pattern.** The water stream sprays in multiple directions or has visible holes in the stream pattern. Individual screen holes are blocked while others are clear.
**Leaking at the spout tip.** Water dribbles or drips from around the aerator housing when the faucet is off. The aerator o-ring or washer is worn and needs replacement.
**Visible white or greenish deposits.** Calcium carbonate (white scale) or copper oxidation residue (greenish) is visible on the aerator face or at the spout tip.
**Sudden change after a supply line interruption.** When water supply was recently shut off for plumbing work or utility maintenance, particles disturbed from the supply lines may have deposited in the aerator screens. Cleaning after supply interruptions is standard maintenance.
### Removing the Aerator
**External thread aerators** unscrew counterclockwise (righty-tighty, lefty-loosey applies). Try hand removal first. If the aerator will not budge by hand, wrap the aerator housing with a cloth to protect the finish and use slip-joint pliers or channel-lock pliers, gripping across the flat sides of the housing if they are present. Apply steady turning force without crushing the housing. For aerators that have been in place for many years on hard water, mineral scale may have bonded the threads. Spray a small amount of white vinegar around the threads and allow it to soak for 30 minutes before attempting removal again.
**Internal (cache) thread aerators** require the specific removal key that ships with the faucet. The key is a plastic or metal insert that fits the internal thread pattern of the aerator housing. Insert the key, turn counterclockwise, and unscrew. If you do not have the original key, aerator removal keys are available from faucet manufacturers and plumbing suppliers in sets that cover common thread patterns.
### Disassembling and Cleaning the Aerator
With the aerator removed, disassemble it over a cloth or small container to avoid losing small components. A typical aerator stack from front to back:
1. The outer housing (metal or plastic, threaded)
2. A rubber washer or o-ring
3. A flow restrictor (usually a plastic disc with a small central hole)
4. One or more wire mesh screens (usually two)
5. A plastic or metal housing body
Lay out the components in order on the cloth. This matters for reassembly -- the screens must go back in the same orientation.
**Cleaning mineral scale from aerator screens.** Soak all metal components in white vinegar for 1 to 2 hours. For stubborn scale, use full-strength white vinegar or a diluted CLR solution (follow CLR package directions for plumbing component use). After soaking, use a stiff toothbrush or small parts brush to scrub the mesh screens under running water. Hold the screens up to light to verify that the mesh holes are clear before reassembly.
**Cleaning the aerator housing interior.** Mineral scale also deposits inside the housing threads and against the washer seat. Scrub the interior of the housing with the toothbrush after soaking.
**Rubber washer condition.** If the rubber washer or o-ring is hardened, cracked, or compressed flat, replace it. Standard aerator washers are available at any hardware or home improvement store for a few cents. Installing a worn washer back into the aerator is the most common cause of a dripping faucet tip after aerator maintenance.
### When to Replace Rather Than Clean
Aerator screens are fine metal mesh that cannot be repaired once the mesh is torn. If any screen shows holes in the mesh from physical damage (from a tool or from grit that abraded through), the screen must be replaced. Replacement aerator kits with screens and washers sized to your faucet's thread are available from the faucet manufacturer or at plumbing supply stores. Universal replacement aerator assemblies are available at home improvement stores in common sizes.
If the aerator housing itself is visibly corroded, cracked, or the threads are stripped, replacement of the full housing is the right approach. A replacement aerator of the correct thread size and GPM rating costs $4 to $12 at a home improvement store.
### Hard Water and Aerator Maintenance Frequency in Tampa Bay
Hillsborough County's municipal water from the Floridan Aquifer has a hardness of approximately 10 to 15 grains per gallon depending on the specific zone of the supply system -- this is classified as very hard, among the highest mineral content in common US municipal water supplies. The practical effect is that aerators in Tampa Bay homes need cleaning every 6 to 12 months, compared to every 2 to 3 years in areas with moderately hard water and every 5 years or more in soft water regions.
If you notice the aerator clogging faster than 6 months after cleaning, consider a whole-house water softener or a dedicated point-of-use filter upstream of the kitchen faucet. Soft water dramatically extends the interval between aerator cleanings and also protects other plumbing fixtures, water heater elements, and appliances from mineral scale buildup.
Best Bay Services handles plumbing fixture maintenance including aerator service, faucet repair, and supply line replacement throughout Brandon, Valrico, Riverview, Seffner, Plant City, Lithia, and the broader Tampa Bay area. Call (813) 416-8676 to schedule.
Need Professional Help?
Let James handle it, call for a free estimate today.
James has over 10 years of experience in home repair and maintenance throughout Tampa Bay. He founded Best Bay Services to bring honest, quality handyman work to local homeowners, landlords, and property managers.