Exterior CBS Block Paint Preparation Guide for Tampa Bay Homes
By James Evans
## Exterior CBS Block Paint Preparation Guide for Tampa Bay Homes
Concrete block construction -- CBS (concrete block structure) or CMU (concrete masonry unit) -- dominates Tampa Bay's residential housing stock from the 1950s through the present. It is an excellent building system for Florida's climate, but it has surface characteristics that require a different preparation approach than wood or fiber cement siding. Paint applied without proper CBS surface preparation peels within two to three years; paint applied over correctly prepared CBS in the right paint system lasts 10 to 15 years under Tampa Bay conditions. Best Bay Services handles exterior CBS block prep and painting throughout the Tampa Bay area.
### Why CBS Block Is Different from Wood-Frame
Wood-frame homes have a continuous exterior surface of siding, fiber cement board, stucco over wire lath, or similar. CBS block homes have a surface of block faces, mortar joints, an elastomeric or acrylic stucco coat (typically 3/8 to 1/2 inch thick), and paint on top of that. The masonry substrate -- block and mortar -- is alkaline, porous, and subject to two Florida-specific problems that wood never sees: efflorescence and carbonation cracking.
**Alkalinity.** Fresh concrete and mortar are strongly alkaline (pH 12 to 13). Many paints fail on fresh concrete because the alkali saponifies (breaks down) the paint film from beneath. This is why a masonry-specific primer or alkali-resistant primer is required for new or freshly repaired CBS block, not a standard wood primer.
**Porosity.** CBS block and masonry stucco are porous. Moisture enters the pores from rainfall, humidity, and ground wicking. When that moisture evaporates under Florida's sun, it carries dissolved calcium and magnesium salts to the surface, depositing them as the white mineral crust called efflorescence. Paint applied over efflorescence peels as the salts continue to crystallize beneath the paint film.
**Thermal movement.** CBS block is dimensionally stable, but the mortar joints and the block-to-stucco interface are subject to minor thermal movement over decades. Tampa Bay's temperature cycling between 55 degrees in winter and 95 degrees in summer creates enough movement to crack mortar joints and open hairline fractures in the stucco coat.
### Step 1: Pressure Washing
Before any surface evaluation or repair, the entire exterior must be pressure washed to remove dirt, mold, mildew, loose paint, and chalking. Mold and mildew are universal on Tampa Bay CBS block homes due to the humid subtropical climate and shade from vegetation.
**Pressure settings for CBS block:** 1,200 to 2,500 PSI with a 25-degree (green tip) or 40-degree (white tip) nozzle. Avoid 0-degree or red-tip nozzles -- they concentrate pressure enough to damage mortar joints or gouge soft masonry.
**Add a mildewcide to the wash water.** Mix 1 cup of bleach per gallon of water in the pressure washer's chemical injection system, or apply a mildewcide solution with a garden sprayer before pressure washing. This kills mold and mildew at the surface level rather than just removing visible growth. Allow the bleach solution to dwell for 10 minutes before rinsing.
**Allow full drying before proceeding.** CBS block is porous and retains moisture. After pressure washing, allow at least 48 to 72 hours of dry weather before applying any coatings. In Tampa Bay's rainy season, this may require scheduling around daily afternoon thunderstorms.
### Step 2: Efflorescence Removal
After washing and drying, inspect the entire surface for efflorescence -- the white, chalky, or crystalline deposits visible at the surface. These must be mechanically removed before painting.
**Wire brush.** A stiff wire brush removes light to moderate efflorescence from flat block faces and mortar joints. For large areas, a wire cup brush attachment on an angle grinder speeds the process significantly.
**Muriatic acid wash.** For heavy efflorescence that wire brushing cannot remove, a diluted muriatic acid solution dissolves the calcium carbonate deposits. Mix 1 part muriatic acid to 10 parts water (always add acid to water, never the reverse). Apply with a stiff brush, allow 5 to 10 minutes of reaction time, then rinse thoroughly with water. Neutralize the surface with a baking soda solution (1 cup per gallon of water) before final rinse.
**Safety for muriatic acid work:** Muriatic acid is a strong corrosive. Wear chemical-resistant gloves, eye protection, and old clothing. Protect landscaping from runoff. Work in sections no larger than what you can scrub and rinse in 10 minutes.
After efflorescence treatment, allow the surface to dry completely before proceeding.
### Step 3: Crack and Joint Repair
Inspect all mortar joints and the stucco surface for cracks. CBS block homes in Tampa Bay commonly show:
**Hairline stucco cracks** from thermal cycling over 20 to 40 years. Hairline cracks (less than 1/16 inch wide) can be bridged by an elastomeric paint system without specific repair if the cracks are stable. Wider cracks require filling before painting.
**Mortar joint deterioration.** Open or crumbling mortar joints allow water entry behind the stucco coat, promoting the staining, efflorescence, and biological growth cycle. Rake out loose mortar 3/4 inch deep and repoint with Type S mortar mix (appropriate for Florida's exterior exposure). Allow new mortar to cure 7 to 14 days before painting over it.
**Stucco fractures.** Cracks wider than 1/16 inch should be filled with an elastomeric caulk or a masonry repair caulk before painting. Use a caulk that is rated for masonry and that accepts paint -- not silicone, which does not accept paint. Smooth flush with the adjacent surface.
**Block corner spalling.** Physical damage to block corners (from impact or corrosion of embedded rebar in older blocks) requires patching with vinyl-modified cement patch compound, feathering smooth, and priming before painting.
### Step 4: Primer Selection
Primer is not optional for exterior CBS block work. The primer choice depends on the surface condition:
**Alkali-resistant block filler primer:** The standard choice for bare masonry, new stucco, or heavily repaired areas. Block filler penetrates the pores of the masonry and fills the surface texture, reducing the amount of topcoat needed and providing an alkali-resistant barrier. For bare or repaired sections, this is the correct primer.
**Bonding primer over existing paint:** When repainting over existing paint that is in sound condition (no peeling, good adhesion), a masonry bonding primer can be used to improve adhesion of the new topcoat over the old paint film.
**Direct-to-stucco acrylic primer:** For stucco surfaces with sound existing paint, a masonry-specific acrylic primer is typically sufficient.
Avoid applying any paint system over CBS block until the primer cures to manufacturer specifications -- typically 2 to 4 hours for acrylic primers, 24 hours before topcoating.
### Step 5: Topcoat Selection for Florida's Climate
**Elastomeric masonry paint** is the premier choice for Tampa Bay CBS block homes. Elastomeric coatings are thick-film paints formulated to bridge hairline cracks (up to 1/32 inch) and flex with the thermal movement of the substrate. They resist water entry at the surface and release moisture vapor from beneath (breathable), which is critical on a masonry substrate. Applied at 10 to 20 mils dry film thickness, elastomeric coatings protect CBS block far better than standard acrylic paint.
**100% acrylic masonry paint** is the standard alternative when the surface is in good condition and no crack-bridging performance is needed. Florida's UV intensity demands exterior acrylic paints with UV inhibitors -- generic interior-grade acrylic paint degrades visibly within a year on Tampa Bay exterior surfaces.
**Reflective (cool roof) coatings** are available for flat or low-slope roof sections of CBS block homes and can reduce attic temperatures meaningfully in Florida's solar environment.
### Application Notes for Tampa Bay Conditions
Apply exterior paint only during favorable conditions: temperatures between 50 and 90 degrees Fahrenheit, humidity below 85%, no rain forecast for 24 to 48 hours, and no direct sun on the surface being painted (follow the shade around the house). Tampa Bay's rainy season (June through September) makes scheduling difficult -- most exterior paint projects are best completed October through May.
Apply two coats of elastomeric topcoat, allowing the first coat to cure per manufacturer recommendations. Backroll after spraying if using an airless sprayer to work the paint into the surface texture.
Best Bay Services handles exterior CBS block prep and painting throughout Brandon, Valrico, Riverview, Seffner, Plant City, Lithia, and Thonotosassa. Call (813) 416-8676 to schedule an exterior paint assessment.
Need Professional Help?
Let James handle it, call for a free estimate today.
James has over 10 years of experience in home repair and maintenance throughout Tampa Bay. He founded Best Bay Services to bring honest, quality handyman work to local homeowners, landlords, and property managers.